Plumbing Basics: What You Need for Bathtub Installation
Plumbing Basics: What You Need for Bathtub Installation
Blog Article
What're your opinions concerning Tools You Need to Install a New Bathtub ?
Mounting a bath tub isn't specifically brain surgery, however it does need strong plumbing, woodworking, and also occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately difficult task. If the old bathtub is easily obtainable, the task can move immediately; if you need to open up a wall surface to remove the old bathtub and also place the new tub, the task is much harder. In either situation, the project is within a house handyman's abilities, although you will certainly require a helper to vacate the old tub as well as embeded in the brand-new one. See to it you have qualified yourself for the job and fit attempting it. As opposed to working with a contractor to take control of a halfway-completed task, it is much better to think about using one before you begin. Chances are you might require a professional plumber to make tube links.
This post will certainly assist you mount a new bath tub in your shower room if you have actually currently purchased a brand-new bathtub and don't need to alter the setup of your previous water system pipelines.
Your devices and material checklist should make up the following:
Getting ready for the Setup
To start with, the sustaining structure supplied with the bathroom should be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to make certain that if the faucet features a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps device to stop pressure on the bath tub.
Fit the versatile tap ports to the bottom of the two taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its last placement.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water. After doing so, switch on the faucets to drain any water staying in the system. The procedure of removing the existing faucets can be quite bothersome due to the restricted access that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will certainly originate from the pipes. As soon as the supply pipelines have been removed, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old sealing compound.
Before moving on to fit the new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Installing the Tub
Utilizing both wood boards under its feet, place the bath tub in the required setting. The wood boards are handy in evenly spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by examining the level as well as readjusting the feet on the tub until the level checks out level.
To mount taps, fit all-time low of the outermost adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the very same for the other faucet.
Switch on the water system and examine all joints as well as brand-new pipework for leakages and tighten them if essential. Fill the tub and likewise inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the manufacturer's instruction manual. Tiling and also securing around the tub should wait till the bathtub has been utilized at least when as this will certainly settle it right into its last placement.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic port to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and the other end supplies a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will call for reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin guaranteeing that the washing machines remain in area in between the faucet and also the sink. Protect the faucet in place with the manufacturer supplied backnut. Once the tap is securely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap adapters. The previous type must be attached to the faucet ends first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a stiff seal, triggering the water to penetrate the wall between the bathroom as well as the tiling, resulting in problems with dampness and also feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your fixtures and also fittings. They are offered in tubes and also cartridges, and also are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill the bathtub with water before sealing, to enable the activity experienced when the bathtub is in usage. The sealer can fracture rather early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles making use of water-resistant or water-proof glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was shown that report on Tools You Need to Install a New Bathtub from an acquaintance on another web page. Sharing is caring. You won't know, you will be helping someone out. We take joy in reading our article about Installing A Bathtub.
Avoid more damage, call now! Report this page